Tuesday, September 25, 2012


PIC18F44K22 MCU CRACK,microchip chip decrypt, chip code

extraction, pic chip crack, pic chip clone, microchip chip

products clone.PCB cLone.

High Performance RISC CPU:
C Compiler optimized architecture/instruction set
Data EEPROM to 1024 bytes
Linear program memory addressing to 64 Kbytes
Linear data memory addressing to 4 Kbytes
Up to 16 MIPS operation
16-bit wide instructions, 8-bit wide data path
Priority levels for interrupts
31-level, software accessible hardware stack
8 x 8 Single-Cycle Hardware MultiplierExtreme Low-Power

Managementwith nanoWatt XLP™:
Sleep mode: 100 nA, typical
Watchdog Timer: 500 nA, typical
Timer1 Oscillator: 500 nA @ typical 32 kHzFlexible Oscillator

Precision 16 MHz internal oscillator block:- Factory calibrated

to ± 1%- Software selectable frequencies range of31 kHz to 16

MHz- 64 MHz performance available using PLL –no external

components required
Four Crystal modes up to 64 MHz
Two external Clock modes up to 64 MHz
4X Phase Lock Loop (PLL)
Secondary oscillator using Timer1 @ 32 kHz
Fail-Safe Clock Monitor:- Allows for safe shutdown if peripheral

Two-Speed Oscillator Start-upSpecial Microcontroller Features:
Full 5.5V operation (PIC18F2XK22/4XK22)
Low voltage option available for 1.8V-3.6V operation

Self-reprogrammable under software control
Power-on Reset (POR), Power-up Timer (PWRT)and Oscillator Start

-up Timer (OST)
Programmable Brown-out Reset (BOR)
Extended Watchdog Timer (WDT) with on-chiposcillator and

software enable
Programmable code protection
In-Circuit Serial Programming™ (ICSP™) viatwo pins
In-Circuit Debug via two pinsAnalog Features:
Analog-to-Digital Converter (ADC) module:- 10-bit resolution- 17

analog input channels (PIC18F/LF2XK22)- 28 analog input channels

(PIC18F/LF4XK22)- Auto acquisition capability- Conversion

available during Sleep
Programmable High/Low Voltage Detection(PLVD) module
Charge Time Measurement Unit (CTMU) formTouch™ support:- Up to

28 channels for button, sensor or sliderinput
Analog comparator module with:- Two rail-to-rail analog

comparators- Comparator inputs and outputs externallyaccessible

and configurable
Voltage reference module with:- Programmable On-chip Voltage

Reference(CVREF) module (% of VDD)- Selectable on-chip fixed

voltage referencePeripheral Features:
24/35 I/O pins and 1 input-only pin:- High current sink/source

25 mA/25 mA- Individually programmable weak pull-ups-

Individually programmable interrupt-on-pinchange
Three external interrupt pins
Up to seven Timer modules:- Up to four 16-bit timers/counters

with prescaler- Up to three 8-bit timers/counters- Dedicated,

low-power Timer1 oscillator
Up to two Capture/Compare/PWM (CCP) modules
Up to three Enhanced Capture/Compare/PWM(ECCP) modules with:-

One, two or four PWM outputs- Selectable polarity- Programmable

dead time- Auto-shutdown and Auto-restart- PWM output steering

Two Master Synchronous Serial Port (MSSP)modules with two modes

of operation:- 3-wire SPI (supports all 4 SPI modes)- I2C™

Master and Slave modes (Slave modewith address masking)
Two Enhanced Universal Synchronous AsynchronousReceiver

Transmitter modules (EUSART):- Supports RS-232, RS-485 and LIN

2.0- Auto-Baud Detect- Auto Wake-up on Start bit

No comments:

Post a Comment